- Видео 15
- Просмотров 2 520 890
moomoo97
Добавлен 6 сен 2006
The Devil Is In The Details.
Quick Tips: Ford Focus ST Manual Transmission Fluid Drain & Refill Plugs
Tips on how to loose the drain plug in tight space and also show you the alternative factory fill-hole of the Focus ST Manual Transmission for easier refill.
Suggested tools for this task: 8mm Hex Socket or Key, Wrench, extension & Ratchet
Dual Clutch Transmission Fluid, Motorcraft P/N XT-11-QDC
or equivalent meeting Ford spec. WSS-M2C200-D2.
1.8 Quarts Filled
Plugs Torque Specs: 26 ft/lbs
Always proceed with caution when working on cars. Subscribe to my channel for more future videos. When In Doubt, RUclips!
Suggested tools for this task: 8mm Hex Socket or Key, Wrench, extension & Ratchet
Dual Clutch Transmission Fluid, Motorcraft P/N XT-11-QDC
or equivalent meeting Ford spec. WSS-M2C200-D2.
1.8 Quarts Filled
Plugs Torque Specs: 26 ft/lbs
Always proceed with caution when working on cars. Subscribe to my channel for more future videos. When In Doubt, RUclips!
Просмотров: 35 530
Видео
How To Replace Ford Focus Tail Lights with LED lights
Просмотров 90 тыс.9 лет назад
Check out my How-to video for the Tail Lamp removal steps. ruclips.net/video/M0_9UP6U4s8/видео.html Check out my video about the tail lamp bulb replacement guide. ruclips.net/video/va4RTt8J-9Y/видео.html How to replace Ford Focus Mk3 (2012 model year) standard tail lights with long-lasting Philips Vision LED lights. They are a direct replacement for incandescent bulbs and are resistant to extre...
Standard Incandescent Bulbs VS Philips Vision LEDs
Просмотров 19 тыс.9 лет назад
Standard incandescent bulbs actually take a little time to light up. But Philips Vision LED lights turn on instantly. That means, when you brake, the vehicle behind you can react sooner. The instant-on response provided by the LED lights can reduce braking distance by up to 20 ft. at a speed of 75 mph. The light output of the Vision LED lights also produce a well-focused beam of light even when...
How To Replace Ford Focus Battery
Просмотров 816 тыс.11 лет назад
How to change or remove the car battery in your Ford Focus Mk3 (2012 model year). This video will give you a visual guide for this DIY. Just be prepare to work in tight space and take this 40 lbs object in & out of the car..... Suggested tools for this task: 10mm Socket, Ratchet & in-lbs Torque Wrench Genuine Ford/Motorcraft Car Battery Group# 96R Battery Terminals Torque Specs: 60 in-lbs Alway...
Ford Focus Hood QuickLIFT System Mod - Get Rid Of The Hood Prop Rod!
Просмотров 41 тыс.11 лет назад
The 2012 (Mk3) Ford Focus comes with factory hood prop rod, which always gets in the way when working on the engine bay. Here the hood QuickLIFT System from Redline Tuning comes to the rescue. Their QuickLIFT Hood Strut Kit features a simple, bolt-on installation and comes only with high quality parts. Installation is also quick and easy. Suggested tools for this mod: 10mm & 13mm Deep Sockets, ...
How To Replace Ford Focus Cabin Air Filter
Просмотров 871 тыс.11 лет назад
How to replace cabin air filter in your Ford Focus Mk3 (2012 model year). This video will give you a visual guide for this DIY. Just be prepare to work in tight space and test your dexterity. Suggested tools for filter cover screw: T15 Torx Bit Screwdriver Genuine Ford/Motorcraft Cabin Air Filter Parts# FP70 A cabin air filter is an air purification filter designed to remove the microscopic dus...
Ford Focus Aftermarket Footrest / Dead Pedal Mod
Просмотров 42 тыс.11 лет назад
The 2012 Ford Focus has no cover over the footrest area, just the same carpet as the rest of the floor. That area will mostly be used often but hard to keep clean with just the carpet. With the addition of this aftermarket footrest/dead pedal, it will give a cleaner look and aesthetically pleasing in that area. The aftermarket pedal showcased in this video is from eBay, just search for 'Ford Fo...
Ford Focus Tail Lamps Details And Bulbs Replacement Guide
Просмотров 67 тыс.11 лет назад
Check out my How-to video for the Tail Lamp removal steps. ruclips.net/video/M0_9UP6U4s8/видео.html Check out my How-to video about LED bulbs conversion. ruclips.net/video/vy pqH_1VQ/видео.html This video mainly talks about Ford Focus Mk3 (2012 model year) 5-door tail/rear lamp assembly with its bulbs location and their replacement guide. Tips on how to convert them to LED bulbs, etc. informati...
How To Remove Ford Focus Tail Lamp Assembly
Просмотров 183 тыс.11 лет назад
Suggested tools for tail lamp removal: BIG Flat-Head Screwdriver Check out my video about the tail lamp bulb replacement guide. ruclips.net/video/va4RTt8J-9Y/видео.html Check out my How-to video about LED bulbs conversion. ruclips.net/video/vy pqH_1VQ/видео.html How to remove Ford Focus Mk3 (2012 & above model year) tail/rear lamp assembly. It's the only way to gain access to all the light bulb...
How To Reach & Replace Ford Focus Fog Lamp Bulbs
Просмотров 130 тыс.11 лет назад
Check out my How-To video for the Headlamp removal steps first. T30 Torx Bit or Flat-Head Screwdriver is all you need. ruclips.net/video/Ota7jQ7Iu88/видео.html How to reach and replace Ford Focus Mk3 (2012 & above model year) fog lamp bulbs. By going through the head lamp openings, this is probably the easiest way to change out the fog lamp bulbs without a lot of disassembly work (wheels & whee...
How To Remove Ford Focus Headlamps Assembly
Просмотров 32 тыс.11 лет назад
Suggested tools for headlamps removal: T30 Torx Bit Or Flat-Head Screwdriver. Check out my How-To video for Fog Lamp Bulbs Removal too. ruclips.net/video/P0u5mC7txK0/видео.html How to remove Ford Focus Mk3 (2012 & above model year) headlight enclosure. It's the only way to gain access to all the light bulbs inside for replacement and with a bonus to easily reach the fog light bulb too. This vid...
How To Replace Ford Focus Side Marker & Puddle Lamps To LED
Просмотров 95 тыс.11 лет назад
This video will show you how to replace Ford Focus Mk3 (2012 model year) side marker and puddle lamps to LED. You can also use this as a guide to replace the regular light bulbs in your Focus' side mirrors. Have Fun! Always proceed with caution when working on cars. Subscribe to my channel for more future videos. When In Doubt, RUclips!
How To Replace Ford Focus 5-Door Cargo Lights To LED
Просмотров 37 тыс.11 лет назад
This video will show you how to replace Ford Focus Mk3 (2012 model year) 5-Door hatchback trunk/cargo light bulbs to LED. You can also use this as a replacement guide to change the regular burned-out bulbs on your Focus. Have Fun! Always proceed with caution when working on cars. Subscribe to my channel for more future videos. When In Doubt, RUclips!
California Screamin' Roller Coaster Riding At Disney California Adventure Park
Просмотров 2,6 тыс.11 лет назад
California Screamin' roller coaster riding experience at Disney California Adventure Park Paradise Pier section. This is the longest, fastest and most FUN roller coaster compare to other similar attractions at the whole Disneyland park! Tips: Use the FastPass on this one, long wait time is expected.
How To Replace Ford Focus Radial Engine Air Filter
Просмотров 60 тыс.11 лет назад
How to replace engine air filter for your Ford Focus Mk3 (2012 & above model year with Radial-type air filter). It's a simple DIY not only for fun but it will also save you time & money from a trip to the dealership. Genuine Ford Air Filter is used in this video, but it'll also apply to other compatible aftermarket air filters. Have Fun! Always proceed with caution when working on cars. Subscri...
Y(OU cant reach the negative on a Ford Connect!!! YOu are lucky
@@stuartmenzies3928 There’s metal stud poke-out by the hood hinge for Negative Terminal on the Ford Connect.
Can you put subtitles on these videos….
Thanks Ford for making my life so easy
Thank you so much for your video! It is still so so helpful to see how to do this even 9 years later! I’ve never changed my filter in my 2015 ford focus since inheriting it back in 2019. Man oh man is the old filter FILTY!! My lungs thank you for this tutorial 🎉
Have had my Focus for over 10 years and every couple of years I come back here for a refresher.
One of the best videos I've ever seen! Great job!!!! 🙂
Why does this show up when I'm looking for the 2008 focus
Excellent video, thank you very much kind sir
Do you know if there is a fuse for the puddle lamps? Both were stopped working but the directional mirrrors and turn signals still work
Good detailed video! Wish I'd seen it before, as I had a dead battery in my C-Max and I couldn't figure out how to take it out. Unfortunately, on a 2012 C-Max, although very similar to the Focus, it's much more difficult to remove the battery, because it's bigger (start/stop type) and the cover goes all the way back (not split in two, like the Focus). You need to remove the air filter and completely disengage the power distribution panel (tilting it like you did, is not enough), to get the room needed - the battery is much longer and weighs 22kg, making it hard to slide out in such a tight space!
This is a great tip for the Focus ST, I will also spray parts cleaner around the fill plug before I remove it so that no debris can fall in the hole when I remove it.Subscribed.
Thanks for the tips to change my 2015 ford focus cabin filter. I appreciate the t15 torx bit info. I tried 4 other bits that didn't fit. Also, I like the method of squeezing the filter to install the new filter. I wonder if I could use a price of 1" gift wrap ribbon of the appropriate length to tie it off to squeeze it. Then remove the ribbon after installation... What do you think about that?
new battery i put in but still error message my battery need service..How to reset BMS without scan tool??? anyone?...
I unplug the grey clip but when I try to pull the bulb out it's still attached with 2 metal wires or something
I never took off any of the trim that surrounds the negative terminal of the battery, I just slid a 10 mm ratchet spanner under there.
Thank you for this video. I am having to replace the battery in my 2015 Ford Focus after below temps & it needed a fresh battery anyway. Your video is detailed, and easy to view and understand, making it less overwhelming since I am an older woman. I cannot understand why car makers just don't make the battery compartment directly in the front to have easy in and out removal/insertion like the cars from years again. All this new stuff and plastic is ridiculous. But you made this look easy, I hope it is when I start on my battery. 😀
Hello, my car battery died this cold morning and I'm thinking of taking it off and recharge it in house to give it some life. I see this US based battery whichs seems smaller than EU version? Can I get mine off without taking the airinlet off even if the battery is slightly bigger? My model is 2017 1.5tdci with start/stop battery. I'm afraid I break something when taking off air filter etc cables. Guess I can try but its so cold outside. Also how I reprogram the battery, or do i need to to do it if I just use the same battery which it had. Does it lose memory of my battery when taking it off for a day to recharge indoors?
@moomoo97 I know this was 8 years ago. I recently bought these 7443R Philips vision led bulbs. They are very hard to find them nowadays. I love this design and use our reflectors. What I don’t like is the color of the red led. When it’s on, it was orange-ish red. And it does not create a usable light. That’s why I still use the sylvania zevo 7443R brake lighted bulbs. Those create a nice rich red that’s more deeper and vibrant. And the Philips are 12 year warranty. While the sylvania zevo are a lifetime warranty. I love both led that uses our reflector housings. But I didn’t like the color it makes: With 4 LED’s, the beam pattern of my red tail lights were a wider and more square shape beam pattern vs. the zevo makes just wide rectangular shape. But the zevo red led were more usable beam pattern, the Philips vision were less bright or less usable light.
I think I'd cover the + terminal with a rag to prevent accidentally touching it with a ratchet or other tool and shorting
🔥🔥🔥🔥
Ford why oh why do you have to make things so damn difficult , most car's have them in the engine bay and it's a simple switch
You are doing it completely wrong - aligning it to the tabs first and then forcing the tubular side onto the pipe ending? Why would you do that??? You should put the open side of the filter onto the intake pipe opening first, then move the closed end down, behind the tabs. It is intended that way by Ford! This way you won't break the tabs and you don't have to force anything - it just snaps into place, the closed end goes into its groove in the housing. That's all! Please don't spread this nonsense, look at all the comments, others broke their filter housings because of bad instructions! And it is expensive to buy a new one, even a broken housing will let debris and dirt in!
Thank you for your generosity in going to the trouble of sharing this knowledge with the rest of us. It may seem simple but to the non mechanic its just a bunch of puzzle pieces.I have A 2007 Australian model that has a slightly different cross brace set up but your video solved it.
What if my wires are messed up?
From uk my right hand drive focus 65 plate was very similar though there is a very frustrating additional cable in the way of the filter aperture.
MooMoo, just when I thought I had pretty well learned a bunch about the ST, you come along with this alternate fill plug that NOBODY ELSE has ever mentioned before. When I was loosening the normal fill and drain plugs I discovered that the fill plug was only hand tight (actually hand loose). That now explains the lubricant film all over that side of the engine compartment. Thanks for the great video and new information. DGBryan
Thanks for watching & comments. It's unfortunate that the lower-fill plug is at an awkward location for easy loosening/tightening. That's why I suggested that top-fill plug location for DIYers here, though it requires a little bit work to remove the air filter box first. Glad to know this video is still helpful to anyone with the ST :)
My ST is a ‘13 with only ~60k miles. I think it’s time to do all the fluids. This is one of the ones i want to do. 😊
Cheers mate saved me a fortune in cash
Excellent! 😄
Watched a similar video on here , the guy removed the full air box directly in front of the battery to slide it out. I thought at the time that can't be right and after watching this video i was right, glad this video popped into my to veiw box.
Ford engineering. It really sucks.
Thanks for the vid - just the job :) It's comprehensive so watching how to do it took longer than actually doing it! Saved me £££ calling in a mobile mechanic, which was the alternative. So a Grateful Viewer here - Cheers
Bout gave up until I saw this thank you sir and fuck ford for this
Will this method work on a focus RS? Anyone know
Best tutorial video of all time.
I broke my Air Filter Clips on the Air Filter box trying to force the Air Filter into the unit. Following day, I removed the cover again and used a Grease on the filter lip and on the intake flue. It went in like a glove. I used Easy Grease ‘Easy Grease Spray Lubricant Synthetic Oil Waterproof Rust Protection’ from Amazon but you can possible use any other which can withstand -20 to +120 degrees. PS mine was original Volvo Filter. Same recommendation applies for Ford and others.
Thank You Everybody for All that you are doing for our Planet Earth.. Peace Shalom Salam Namaste 🙏🏻 😊 🌈 ✌ ☮ ❤ 🕊
Kind Sir! I am 64 years old and have changed car batteries in the past. My wife’s 2012 Ford Focus battery died in the frigid cold on Christmas Eve this year (2022). The battery is in a cramped space with some slightly tricky maneuvers needed. After viewing a few videos I came across your fine video and found that your instructions were absolutely perfect. My wife, with my help, replaced the battery with minimal frustration. Your guidance was essential and greatly appreciated! Thank you so much! Your video was perfect, very clear and detailed! I wouldn’t change a thing! Thanks, again! Love and Peace to you and your family from Bryan and Ellie!
I could take my steal toe to the rump of whomever thpught this design was a good idea😑 thankfully im not a feeble female so i should b ok
Battery store didn't want to change out my battery. The guy said to watch a RUclips video on this car's problem battery change. You are the best video out of everyone and I feel confident trying it myself. Thank you so much!
Thank You Everybody for All that you are doing for our Planet Earth.... Peace.. Shalom.. Salam.. Namaste .. 🙏🏻 😊 🌈 ✌ 🌷 ☮ ❤🕊
Well explained video.. Thanks for making one
Thanks. This helped me with my 2018 Focus Titanium
Superb - thank you SO much! (Lucky not to follow advice from another RUclipsr who tells you to take off the airbox and unplug stuff - which causes lots of problems!)
I did that but light only worked for a minute or so then went out and did't work again
Ugh
I dont see this on my 2010 ford focus se
Awesome job, thank you!
I did a drain and fill on my 2015 focus st, used oem, although older oil - maybe 1 year old. I filled close to 1.8qt until I had oil pouring out of top port. But now I have transmission wine under load - especially on lower gears. HELP!
My two step lights don’t work left and right
Дядя Петя!Вы дурак!?
Why has no one mentioned you need to reset the ecu after changing the battery and how the heck do you do it?